Build a pretty and easy, chunky DIY Wooden Curtain Rod and brackets.
I looked all over my favorite stores, IRL and online, and couldn’t find the perfect curtain rod and brackets for the boys bedroom makeover. So, I did what any DIY lover would do, and made them. Honestly, when I say this is a Quick & Easy DIY Wooden Curtain Rod and Brackets, I mean it. I bet I had this assembled, painted, and hung in less than 3 hours. So quick, guys!
With this DIY, you can use nearly any brackets you like. And paint or stain them any color you’d like. So, you’ll always get the perfect design and style to match your room. AND, you get to make your own custom width rod too. So, no more buying those adjustable rods. They are always kind of a pain to pull a curtain over, with that hump in the middle. Right?!
Subscribe to Abbotts At Home on YouTube, for the lastest DIY and Home Improvement Videos. Now let’s get this DIY Wooden Curtain Rod build started.
THIS POST MAY CONTAIN AFFILIATE LINKS. AFFILIATES HELP YOUR FAVORITE BLOGGERS DELIVER FREE CONTENT. Make sure to always read the directions for any products or tools you use while building. Read the full disclaimer here.
Materials for this DIY Quick & Easy DIY Wooden Curtain Rod
Note: You can pick any style of bracket or cornice you think would look best. Just make sure you have enough room for the Closet Pole Socket Set (with room to lift the rod in and out). And you want enough depth to keep the curtain the right distance away from the wall too.
- Wood Closet Pole Socket Set
- Wood Closet Pole, in the correct length (you can get this cheaper at Home Depot or Lowe’s)
- 2 Wood Brackets, I find mine at Lowe’s
- Wood Glue & 150-grit Sandpaper
- Optional: Brad Nails and Brad Nailer
- Miter Saw
- Spirit Level
- Paint Brushes or Paint Sponges
- Whichever spray, latex or chalk paint works for you. I used Castle Path by Behr, mixed into a chalk paint with my recipe
- Polyurethane, like Minwax Polycrylic in Clear Matte
Steps to Build
Design Note: I used glue and a brad nail for assembly. BUT, if you don’t have a brad nailer, you could glue, clamp, and let the pieces dry before painting. I just used the brad nailer so that I could move on to painting without waiting. Actually, I should have just used my DAP Rapid Fuse to glue these pieces together. It’s like super glue for wood. Then I could have skipped the nail and still had a very short dry time.
- Decide on best bracket size and design for your space. Make sure it’s big enough for the rod socket, with enough room for lifting the rod in and out of place.
- Cut one end of your bracket off. I think this makes it look more like Curtain Brackets and less like shelf brackets. I cut about 3″ off the end of mine.
- DIY TIPS: Easily make sure you get 2 identical cuts, by clamping a scrap piece of wood to the saw. AND do not cut the rod until you have hung the brackets on the wall. This is how you can be sure to get a perfectly snug fit with the rod. You don’t want to have to buy a new rod, or patch holes in your wall if the rod is too short.
- Mark the placement of the sockets on the brackets. I tested that I could lift the rod in and out of place before deciding where I wanted my socket.
- Glue and clamp and/or nail the sockets to the brackets.
- Wipe away any excess glue with a clean, damp cloth.
- If painting, lightly sand the brackets and rod. If staining, you will need a to completely sand with 150-grit sandpaper. Then apply Wood Conditioner, to prep for stain.
- Apply Paint or Stain. Apply a polyurethane to protect the finish.
- To hang the brackets, use painter’s tape to mark the top of the bracket and where each screw hole should be.
- Then transfer that tape to the wall. I knew I wanted my brackets 4″ below the crown. I used the line marking the top of my bracket as a guide for hanging. I also used a level to make sure that tape was straight before putting the anchors in the wall.
- Once both brackets are hung, measure and cut your rod. Touch up any paint or stain, on the ends, as needed.
- Hang those curtains and enjoy!What do you think? Does it work with the rest of the room, so far?
UPDATE: You can see the Boys Bedroom Full Reveal now. I’d love for you to stop by and check it out. 🙂
Looking for another fun DIY Project? Check out my popular Pour on Two Canvases video, then head here to see the full DIY Wall Art tutorial and all of the pictures from that pour.
Looking for a another easy DIY Home Decor Project? Try this DIY Wood Frame for Canvases or Other Wall Art.
Or add a little style to your home while having fun with your Miter Saw, with this DIY Scrap Wood Wall Art.
Feeling inspired? Get out there and make your own Quick & Easy DIY Wooden Curtain Rod and Brackets. Have fun and let me know if you have questions. Don’t forget to sign up for the Abbotts At Home email newsletter to get DIY, Remodeling, and Crafty ideas in your inbox.